Click here to close the indexes

Click here to open the scrolling images index

Misc Hardware-Grommets-Feet-Ring terminals

You can scroll through the images above using the Image scroll controls.
Or you can use the Left and Right arrow keys on your keyboard.
You can tap on an image to go to that catalog page.

Click here to open the Catalog Index Table

Tube Amp Hardware, Chassis screws, Amp feet

Watch this Shopping cart tips video

Amp feet - Ring terminals - Grommets

Fender screws, nuts and hardware are on this page
Screws, nuts and washers are on this page
Close outs and discontinued items are on my Yard Sale Page Here

Alpha pot washer

Use these washer to center .31 inch diameter shaft Alpha pots in .375 inch chassis holes
.315" inner hole diameter - .371" outer diameter - .036 inches thick
Go to this page to see images of these washers in a couple different chassis
Alpha Pot washers images

Alpha Pots are located on this page
Pots and Knobs Page

This item has quantity discount buttons

Lock Washer for .31 inch pots

(A) Internal Toothed Lock washers for .31 inch bushing Pots
These washers fit all the Alpha amp pots on my pots page
Pots and Knobs Page

Price each = $0.37

Trim Washer for .31 inch pots

(B) Trim washers for .31 inch bushing Pots
These washers fit all the Alpha amp pots on my pots page
Pots and Knobs Page

Price each = $0.10

Nuts for .31 inch pots

(C) Nuts for .31 inch bushing Pots
These nuts fit all the Alpha amp pots on my pots page
Pots and Knobs Page

Price each = $0.10

Lock Washers for .375 inch pots-Jacks

(A) Internal Toothed Lock washers for .375 inch bushing Pots
These washers fit all the CTS amp pots on my pots page
Pots and Knobs Page
They also fit the Switchcraft Jacks on my Jacks and Plugs page
jacks and Plugs Page

Price each = $0.32

Trim Washer for .375 inch pots-Jacks

(B) Trim washers for .375 inch bushing Pots and Jacks
These washers fit all the CTS amp pots on my pots page
Pots and Knobs Page
They also fit the Switchcraft Jacks on my Jacks and Plugs page
jacks and Plugs Page

Price each = $0.29

Nuts for .375 inch Pots-Jacks

(C) These nuts fit the Switchcraft jacks, RCA Jacks and CTS pots that I sell
These nuts fit all the CTS amp pots on my pots page
Pots and Knobs Page
They also fit the Switchcraft Jacks on my Jacks and Plugs page
jacks and Plugs Page

Price each = $1.04

Hex Switch Nut

(A) Knurled Switch nut
These nuts fit all the full sized toggle and foot switches on my Switches page
Switches Page

Price each = $0.29

Sorry, this item is out of stock.

Knurled Switch Nut

(B) Hex Switch nut
These nuts fit all the full sized toggle and foot switches on my Switches page
Switches Page

Price each = $0.29

Sorry, this item is out of stock.

Lock Washer for Switches

(C) Internal Toothed Lock washer for 1/2 inch diameter switches
These washers fit all the full sized toggle and foot switches on my Switches page
Switches Page

Price each = $0.70

Lock Washers for Fender Lamps

(A) internal toothed lock washer for Fender Lamps
These washers fit the Fender lamps on the page below
Lamps Page

Price each = $0.25

Sorry, this item is out of stock.

Shoulder Washer

Insulated shoulder washer
Used to isolate metal jacks from the chassis
Most commonly used with the L12A switchcraft jacks
Inner hole size = .38"
Chassis hole size/Shoulder = .5"
Outer diameter = .63"
You need two of these to insulate a metal jack
My jacks Page is here

This item has quantity discount buttons

Nylon Washer - Marshall jack

Use this washer on the old style Marshall Jacks if your face panel is less than .125" thick
The old Marshall amps had very thick plexi face plates and so no washer was needed
The chrome nut only tightens down so far leaving a .125" gap
The old style jacks come with a thin red fiber washer and so you will need one of these black nylon washers also.
You can see the before and after difference if you look at the larger image on the left
These washers are approx .065" thick
Hole is .44" and Outer diameter is .75"
My jacks Page is here

Price each = $0.32

10-24 Chassis Screw

1.5 inch long Chassis mounting screws
Use this screw with the Rivet nuts and the Clip nuts below
The screw head is a flat blade Truss head
You can cut these shorter these with a hack saw if needed

Price each = $0.29

10-24 Rivet Nut

Install these rivet nuts in a 19/64 inch hole
Use a 10-24 bolt and a #10 washer to compress them
The serrated edge collapses down and grabs the chassis
Chassis thickness range is .02 to .13 inch thick
Use the 10-24 Chassis screws above with these nuts
Wave your mouse over the small images
to see an image of these items installed on a piece of aluminum
Here is a link to Rivnut tools on my amp forum
Price each = $0.27

10-24 Clip Nut

These nuts clip onto the chassis lip
Drill a 11/32 inch hole to make these nuts sit flush against the chassis surface
Use the 10-24 Chassis screws above with these nuts
Wave your mouse over the small images
to see an image of these items installed on a piece of aluminum
Price each = $1.38

9 pin hole blocker plate

(C) Blocks off a 9 pin socket hole
1.15 inch 9 pin screw spacing
Price each = $4.86

#6 Ring Terminal

#6 Round ring terminals for 22-16 gauge wire.
Screw these down to the chassis for an excellent ground connection.
Crimp the wire and then solder for a good connection.
Price each = $0.22

#8 Ring Terminal

#8 Round ring terminals for 22-16 gauge wire.
Screw these down to the chassis for an excellent ground connection.
Crimp the wire and then solder for a good connection.
Price each = $0.25

#8B Ring Terminal-Wire Holes

#8 Round ring terminalswith wire holes
Screw these down to the chassis for an excellent ground connection.
Price each = $0.34

#10 Ring Terminal

#10 Round ring terminals for 22-16 gauge wire.
Screw these down to the chassis for an excellent ground connection.
Crimp the wire and then solder for a good connection.
Price each = $0.20

Rubber Feet

23.6 mm wide X 9.5 mm tall rubber feet for combos and heads.
Metal washer is embedded into rubber for strength.
Price each = $1.18

Rubber Grommets

Used to protect wires that go through the chassis.
Tip: You can cut grommets and then insert them around the wire bundle.

3/16 Rubber grommet

3/16" chassis hole - 1/8" wire hole
The 3/16" grommet is perfect for one or two small wires
Price each = $0.30

3/8 Rubber grommets

3/8" chassis hole - 9/32" wire hole
Price each = $0.52

1/2 Rubber grommet

1/2 inch chassis hole - .31 inch wire hole
Price each = $0.61

5/16 Rubber grommets

5/16" chassis hole - 3/16" wire hole
Price each = $0.21

Sorry, this item has been discontinued.
Go Here for more info

Nylon Nylon

23.6 mm wide X 16 mm tall nylon feet for combos and heads.
Nylon is a harder material than rubber.
Price each = $1.38

Sorry, this item has been discontinued.
Go Here for more info

8 pin hole blocker plate

(B) Blocks off a 9 pin socket hole
1.5 inch 8 pin screw spacing
Price each = $6.64

Sorry, this item has been discontinued.
Go Here for more info

8 Pin to 9 Pin Tube socket adapter

(A) These Adpaters cover a 8 pin Octal tube socket hole and let you bolt in a 9 Pin tube socket
1.9 inches long x 1.34 inches wide
.75 inch 9 pin hole size - 1.15 inch 9 pin screw spacing - 1.5 inch 8 pin screw spacing
Use the #4 screws and nuts on my Screws, Nuts, Washer page
Price each = $6.64

Sorry, this item has been discontinued.
Go Here for more info

Enter My Tube Amp Parts Store Here
Mobile users Enter My Tube Amp Parts Store Here
Hoffman Amps Home	Ordering Information	PayPal info
Returning parts	Sound Clips	What's New
Q and A	Hoffman Links	Shipping Info/policy
E-mail Me	Amplifier Service Technicians	About Hoffman Amps
Hoffman Amplifiers Customer Loyalty Discount Program Information
Search the Hoffman Amps parts catalog
The Tube amp Library of information Click the link above for Tube amp info, Schematics, Board building information. Projects, Mods, Transformer diagrams, Photo's, Sound clips. There are hundreds of pages of Tube amp information on my library page.
Please visit my Tube Amplifier Forum Here's the place you can go to ask tube amplifier questions. You will find a large community of friendly amp builders at the link above.
Check out my huge library of Schematics here
Information: Design your own custom Turret Board or Eyelet board
My on line DIY Layout Creator file analyzer program is here
My DIY Layout Creator file library is here

Mobile Users catalog	Choose a link from the Hoffman Amplifiers parts catalog			Non Stocked Items
Shop by Photo	Wire/Cable	Board Building Parts	Amp trim/Handles	Discount Program Info
Login	Resistors	Hoffman Turret Boards	Tubes/Valves	Misc. Hardware
Logout	Capacitors	Fender Eyelet Boards	Fuses/Cords/AC	Screws/Nuts/Washers
Kits-Parts List	Pots/Knobs	Misc Eyelet Boards	Jacks/Plugs	Tools
Private Parts List	Switches	Custom Boards	Lamps/Diodes	Bike Lighting Parts
Search the Parts Catalog	Tube Sockets	Channel Switching	Chassis	Yard Sale
	-	-	-	What's New